The MiTag Multi-Sensor is a battery powered, long range Bluetooth 5.0, IP67 8-in-1 sensor built specifically for IoT Applications. The MiTag Multi-Sensor packs in more than just an IP67 Temperature Sensor, it also includes Humidity, Pressure, Open/Closed Contact Switch, Light & Motion/Impact Detection, and a Multi-Functional Alert Button with BLE beaconing capabilities.
- Additional information
- CA Proposition 65
|Dimensions||7 × 4 × 1 in|
|Wireless||Bluetooth® 5||Nordic nRF52840 SoC|
|Processor||Cortex M4F||Cortex M4F – 1MB Flash and 256k RAM, 2.4 GHz Transceiver|
|Sensors||Temperature Accuracy||+/- 0.5|
|Pressure Accuracy||+/- 3 % with a +/- 1 % hysteresis|
|Ambient Light||+/- 1 hPa|
|Accelerometer||3-axis MEMS (Programable motion and contact detection)|
|Open/Close Switch||Dry reed switch – Single-pole, Single-Throw (SPST)|
|Battery||Battery life and low power alerting|
|Button||Alert||Multi-Use (Default: Panic Alert)|
|Reset||Reset Switch (Hard)|
|LED||Status Indicator||Multi-State (1 – Red, 1 – Green, 1 – Blue)|
|Antenna||Integrated||Onboard PCB antenna|
|Power||Battery||CR2477 Coin Cell (Replaceable)|
|Storage||Data Logging||8MB NOR Flash – FIFO (Report Logs – TBD)|
|Mounting||Placement||ZIP Tie, Screw, 3M VHB Tape, Mounting Bracket (Removable)|
|Physical||Dimensions||51mm (L) x 51mm (W) x 15mm (H)|
|Environmental||Operating Temperature||-30° to +70°C (Limiting Factor: Coin Cell Battery)|
|Storage Temperature||-40° to +85°C|
|Regulatory||Approvals||FCC, IC, & CE (TBD – In Progress)|
|Customization||Options||Branding (Label, Packaging)|
|Cloud Platform & Web Application (White Labelable)|
WARNING: California Proposition 65
This product can expose you to chemicals including Carbon black and Nickel, which are known to the State of California to cause cancer, and including Bisphenoal A and 1,3-Butadiene, which are known to the State of California to cause birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov
Check Status LEDs
No Status LEDs
Check Software to see for low battery
If state looks normal – Follow directions for new MiTag
Blue Light flashing
Device is out of range of Gateway
Check for physical obstructions
Move MiTag Sensor closer to Gateway or move Gateway closer to sensor
When back in range, MiTag will automatically start to check in
If MiTag sensor is still not checking into the Software, contact support.
Press red panic button for 3-5 seconds to wake:
- If no Status LEDs flash
- Possible for dead battery
- Reset button (5 secs to boot)
- Reseat battery
· Recommendations, take off battery cover and tap, do not use tools (may damage hardware)
I am going to install the MiSensors to a cellular router, how much data does 1 MiTag sensor produce?
Each MiTag produces approximately 100MB of cellular data per month reporting sensors values every 5 seconds.
The MiTag Sensor collects and sends data to our servers every 60 seconds.
Up to 100 Sensors.
-40 to 85°C, Accuracy +/- 0.5 degrees
Yes. It is IP67 rated and can be dropped into a body of water up to a meter deep for up to 30 minutes.
Up to 300 Feet (100 Meters). The signal distance is based on the installation environment. The distance is reduced in environments exposed to interference, such as building structures, materials and radio waves.
Appropriately 2 years. They are replaceable with a Coin Cell CR2477 Battery.
Coin Cell CR2477 Batteries.